أقوى درس فوتوشوب ....... بونيت من الكربون
السلام عليكم ورحمة الله وبركاته
انا يبت لكم درس قوي جدا جدا جدا جدا جدا جدا لدرجة اني ما قدرت اترجمه الدرس في حركات وشغل مضبوط اخليكم مع الشرح والصور بس يا ليت لو تساعدوني لان شي خطوات ما ضبطن معاي :( الخطوة الأولى: السيارة: ![]() الخطوة الثانية : ![]() حدد البونيت "الكبوت" "غطاء المحرك" بعد التحديد اعمل كوبي والصقة يعني بتكون عندك الخلفية ونسخة من البونيت حلووو الكلام؟ ![]() الخطوة الثالثة: افتح صفحة جديدة لا تفتح لير او شريحة لا صفحة جديدة Ctrl + N المقاسات لازم تكون مثل اللي في الصورة ![]() الخطوة الرابعة : الحين تعمل زووم 1600 × للصورة الصغيرة اختار الجرانيت (G) واختار وحدة تكون ابيض واسود كما في الصورة ![]() بتعمل الجرانيت مرتين طبعاً والطريقة هي انك تحدد ربع اليسار الأعلى وتمليه بالجرانيت ثم تحدد الربع اليمين الأسفل وتمليه بالجرانيت مثل اللي في الصورة الخطوة الخامسة: تروح من القائمة الى : ُ Edit >Define Pattern وتسميه اللي يعجبك انا الى هنا فهمت الباقي ما قدرت لأن الطريقة السادسة ما ضبطت معاي :( اخليكم مع الشرح العنجليزي والصور عسا تفهمون وتفيدوني Now this is where it gets tricky. Create a new layer (this should be your third layer) and go: "Edit - Fill" then: Select "Pattern" from the dropdown menu, and click on your Carbon Fiber pattern you just created. After that, you should have an entire layer over the car that is filled with the pattern as seen but the picture on the right. ![]() ________________________________________________ Now to make sure the pattern has that 3D appearance to it, we are going to use: -Edit -Transform -Skew Now drag the corner points inward for the top portion and outward for the bottom portion. Press "enter" to confirm your transformations. Now we have a 3D look. To shake things up, while we are on the CF layer, go: -Edit -Transform -Rotate and rotate the pattern say maybe 30 degrees, so long as the pattern still overlays the hood portion of the car. ![]() ___________________________________________________________ Remember the copy of the hood we made earlier? Time to use it! Hold down "Ctrl" and click on the hood layer. It should make a selection in the shape of the hood. Pretty cool huh? Now, go: "Select - Inverse" then, press "Delete" to erase all the portions of the CF pattern that aren't over the hood. ![]() ___________________________________________________________ Now as to not make a blocky texture, we are going to make sure our selection is the the shape of the hood (Ctrl - click on the hood layer) and go: -Filter -Twirl Use similar settings to the one on the right. ![]() _________________________________________________________ Now make sure your CF pattern layer is active, and change the Layer's Blending mode to "Multiply" as seen on the right ---> To wrap up the package, make the hood layer active and go: "Image - Adjust - Hue/Saturation" Now slide the "Saturation" slider to the left. But not all the way! ![]() ________________________________________________________ Now that should do it! Take a look at the "TIPS" below to strengthen the carbon fiber experience. ![]() ________________________________________ والموضوع الأصلي موجود هنا http://www.photoshopjunkie.com/tutorials/cf/index.htm الصراحة حبيت يكون سوالف اول منتدى يكون فيه الدرس هذا لان كل المنتديات لايوجد فيها الدرس هذا يا ليت لو تحاولون تفهمون بقية الدرس وتفيدوننا لان الحركات ما ضبطن معاي خاصة السادسة اللي هي بداية الانجليزي ولو حد قدر يوضح لنا بالصور بيكون ممتاز وبكون شاكر له كل الشكر انا حاولت اسوي اللي عليه وانتوا حاولوا تساعدوننا وشكراً |
السلام عليكم
تسلم اخوي علي الدرس الرائع فعلا :) |
السلام عليكم
مشكور اخوي كروزر على الدرس . بس اسمحلي اضيف طريقه اسهل واسرع . ياريت يا شباب الي يبغا الدرس يدخل على الرابط . http://y1y1.com/up/Show.php?ID=1110248061-634799958 |
الساعة الآن » 01:45 AM. |
Powered by: vBulletin Version 3.0.16
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.